Under Auto cleaning, if you start the edge cleaning, the robot will walk straight until it collides with obstacles, and will start cleaning along the wall.
The capacity for the dust bin is 0.3L. If will fill up quickly depending on how much debris is on your floor. It can still work when it’s full, however, it cannot store more debris, so it must be emptied when full.
Step1: Aim the remote toward the robot and press the “CLEAN” button to wake the robot when it is in sleeping mode. You will hear 1 beep tone. Step2: While still aiming the remote toward the robot, set the schedule time on the remote that you want the robot to begin cleaning. Step3: When you are done setting the time, press the “PLAN” button on the remote to save your schedule program. You will hear 1 “beep” tone if you have successfully completed the schedule setting program. Note: When you are using the remote to schedule a cleaning time, make sure the remote is close to the robot, or you will not be able to successfully use the scheduling feature. After using the schedule setting feature, ensure the robot is always powered on, otherwise the schedule setting will not work. If you want to cancel the schedule time, adjust the time to 00:00.
1. The HEPA filter may be clogged. Remover the HEPA filter, and clean it with warm water, then let it dry completely, then place it back in the filter slot. If the HEPA filter is over 6 months old, it is advised to replace it with a new HEPA filter. Pick up large items and keep areas to be cleaned open. Clean the side brushes, bristle brush and sensors regularly. Empty the dust bin before using, which will allow for better airflow and efficient cleaning.
This could be caused by multiple issues: Place the vacuum on the charging dock or turn off the power switch when unused. When V5s uses MAX mode, the fan speed becomes higher and suction power increases, which uses more power, thus draining the power quickly. 3. The battery may be damaged/old. Contact technical support if you have tried 1&2 without success.
Turn off the power switch, take out of the dust box and clean off garbage, with the bottom upwards. 1.Check whether the side brush mouth is blocked or not. 2.Check and clean off side brushes.
Repeated cleaning is normal, and the machine works for about 2 hours. Thus, many places need to be cleaned many times in order to achieve a complete clean. Q17.Why does the machine get stuck when transitioning from hard floor to carpet? Make sure the height difference between the carpets and the floor are no more than 15mm. The robot cannot work on the carpet with mop.
Point the remote control at the robot and press the “CLEAN” key – the indicator light will flash for 15 seconds, then, the robot will automatically enter into sleep mode. While in sleep mode, it is necessary to press the “CLEAN” key on the robot or remote controller to awake it.
In the charging process: Three rows of light are gradually added (green light) When charging is completed: Three rows of lights shine for a period (green light) When select the mode: Three rows of lights gradually shine and die out. When the machine fails: Three rows of lights shine at the same time. When the electric quantity is lower: The middle row of lights shine (green light) Recharging mode: The middle row of lights gradually shine and die out. Automatic cleaning status: The middle row of lights shine for a period (green light) Edge cleaning status: The middle row of lights shine for a period, and the lower row of lights shine. Spot cleaning status: The middle row of lights shine for a period, and the upper row of lights shine.
Yes, however, some long hairs will be picked up by the robot will be tangled in the side brushes and bristle brush. Remove accumulated hair periodically.
You can schedule to let the robot start cleaning from a certain time .It will be back to charging base after finishing or low battery. Please press the clean button on remote control , if needs to end early.
This product randomly sets the cleaning route and cannot plan the cleaning route. Fear not, for we plan to introduce these features in subsequent models, so check back periodically!
The battery power is small, and charging will not lead to heats, which is accepted by international experts, and safe and reliable.
This depends on the frequency of use and the cleanliness of the filter. The HEPA filter is generally replaced every two-three weeks. If it is not dirty, it can be replaced every six to eight weeks.
Please fill in water according to the area. It is not required to fill up. If the floor gets close to the carpet, it is advised to block the carpet. To avoid winding, stuck status and water leakage.
The robot will not clean when the mop carries with more water. As for this, take out of the mop and dry the mop.
This product randomly sets the cleaning route and cannot plan the cleaning route. Fear not, for we plan to introduce these features in subsequent models, so check back periodically!
Yes, it does. The robot needs to be charged for 12 hours for the first 3 times in order to fully activate the battery. This will increase the endurance of the battery and ensure a normal battery life.
Charge the robot for three minutes, take off the charger, then charge for three minutes again, and then take off the charger for several seconds. Repeat above actions three times. Finally, charge the robot for 12 hours.